They are making a few great pointers relating to How to Install a Bathtub Yourself as a whole in this post further down.
Setting up a bathtub isn't specifically rocket science, yet it does require strong plumbing, carpentry, as well as sometimes, tiling abilities. Changing an old bathtub with a brand-new one is also a moderately hard project. If the old bathtub is readily easily accessible, the task can move rapidly; if you have to open a wall surface to eliminate the old tub as well as position the brand-new tub, the task is much harder. In either situation, the task is within a house handyman's abilities, although you will need an assistant to vacate the old tub and embeded in the new one. See to it you have qualified yourself for the work and fit trying it. As opposed to working with a professional to take over a halfway-completed project, it is better to consider using one prior to you begin. Chances are you might require an expert plumber to make tube connections.
This write-up will help you mount a new bath tub in your shower room if you have currently gotten a new tub and do not require to transform the arrangement of your previous water supply pipelines.
Your tools as well as product checklist must comprise the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installation, then the first thing you should do is separate the water system. After doing so, activate the taps to drain pipes any water remaining in the system. The procedure of removing the existing taps can be fairly troublesome as a result of the limited accessibility that is typically the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the faucets. Have a cloth ready for the remaining water that will certainly come from the pipes. When the supply pipes have been removed, utilize the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. As soon as the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any old securing substance.
Before going on to fit the new faucets, contrast the pipeline connections on the old taps to the brand-new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the other end offers a link to the existing supply pipes.
If you need to fit a monobloc, then you will require reducing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, place the tap in the installing hole in the bath/basin making sure that the washers are in place between the faucet and also the sink. Protect the tap in place with the manufacturer given backnut. As soon as the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap adapters. The previous type must be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Installing the Tub
Making use of the two wood boards under its feet, place the tub in the called for position. The wooden boards are useful in uniformly spreading out the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 small points.
The next objective is to make certain that the bathtub is leveled all round. This can be accomplished by checking the level and changing the feet on the bath tub till the spirit level reviews degree.
To mount faucets, fit the bottom of the furthest flexible tap connector to the proper supply pipeline by making a compression join; then do the same for the various other tap.
Activate the water system as well as inspect all joints as well as new pipework for leakages as well as tighten them if necessary. Fill the tub as well as also check the overflow outlet and also the normal outlet for leakages.
Ultimately, take care of the bathroom paneling as described in the producer's user's manual. Tiling and also sealing around the bathtub must wait up until the bath tub has actually been used at least once as this will settle it into its final position.
Getting ready for the Setup
First of all, the sustaining structure supplied with the bath needs to be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is necessary to see to it that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps device to stop pressure on the tub.
Fit the versatile tap connectors to the bottom of both faucets utilizing 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you use every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be fitted in its final position.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to split a rigid seal, triggering the water to pass through the wall between the bathroom as well as the tiling, bring about complications with wetness and feasible leaks to the ceiling below.
You can pick from a variety of coloured sealers to blend in your components and fittings. They are sold in tubes and also cartridges, and also are capable of sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with spins of drenched paper or soft rope. Keep in mind to always fill up the bath tub with water before sealing, to permit the activity experienced when the bathtub remains in use. The sealant can split fairly very early if you do not think about this motion prior to securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally conveniently readily available on the market. It is recommended to fit the ceramic tiles utilizing waterproof or water resistant sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
We are very curious about How to Install a Bathtub and I'm hoping you appreciated the new post. In case you appreciated our article plz remember to pass it around. Thanks for your time. Kindly come by our site back soon.
Visit Link